"VIBRAPOD
®"
Isolators
Euro
12,39 / unit
(cadauno)
-
Italia & CE
Tax included
Euro
10,32 / unit
(each)
-
Extra CE
without Tax
Non Più Disponibili - Out of Stock
Piedini in vinile
che isolano dalle vibrazioni, ci sono 5 modelli a disposizione per ogni esigenza
(a partire dal modello 1 il più morbido !) le dimensioni dei vibrapod sono
uniche, (diam mm 63 altezza mm 15) cambia solo la durezza del vinile.
Si utilizzano in
gruppi di 4-6 o più pezzi per apparecchio e/o diffusore, Il miglior risultato
si ottiene con più vibrapod di modello più morbido rispetto a pochi Vibrapod
di modello più duro, riportiamo alcune tabelle che Vi faciliteranno la scelta a
seconda dell'apparecchio da Trattare:
Tabella dei
pesi sopportati da ogni Vibrapod
|
|
|
||
|
|
|
Laserdisc Players & Transports, DAC's, Preamps, Amplifiers, Integrateds, Speakers |
|
|
|
|
Laserdisc Players & Transports, DAC's, Preamps, Amplifiers, Integrateds, Speakers |
|
|
|
|
|
|
|
|
|
Turntables, Speakers |
|
|
|
|
Turntables, Speakers |
Prezzi e prodotti aggiornati sul nuovo sito Audiokit e-Shop cliccando qui !
Update prices & products on new e-Shop Audiokit website click Here
Tabella dei
pesi consigliati per gruppi di Vibrapod in relazione al peso totale
dell'apparecchio.
Ricordiamo che Il
miglior risultato si ottiene con più vibrapod di modello più morbido rispetto
a pochi Vibrapod di modello più duro.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Le
dimensioni per tutti i modelli sono: Diametro mm 63 altezza mm 15
All Models are
9/16" Tall and 2 7/16" Diameter with a Temperature Range of 50°F To
100°F.
Euro
12,39 / unit
(cadauno)
-
Italia & CE
Tax included
Euro
19,32 / unit
(each)
-
Extra CE
without Tax
Non Più Disponibili - Out of Stock
|
|
VIBRAPOD
Isolators may leave rings on woods, acrylics, and painted surfaces. They may
also disolve the paint, especially if it is lacquer. To protect these surfaces
and your equipment please use wax paper or plastic wrap between the VIBRAPOD
Isolators and these surfaces.
Installation Do's
And Don'ts
VIBRAPOD
Isolators may leave rings on woods, acrylics, and painted surfaces. They may
also disolve the paint, especially if it is lacquer. To protect these surfaces
and your equipment please use wax paper or plastic
wrap between the VIBRAPOD
Isolators and these surfaces.
 |
|
|
|
|
|
|
|
|
|
|
In this configuration 8 VIBRAPOD
Isolators will support up to the following weights.
(The use
of 8 VIBRAPOD Isolators above
is to illustrate Symmetrical placement and not a recommendation that you use 8
Isolators per component. You can use as few as three and as many as will fit
around the periphery of a component.)
The following table refers to the
weight 8 VIBRAPOD
Isolators will support as in the example above.
|
|
|
|
|
9.07 kg |
7.25 kg |
10.88 kg |
|
21.77 kg |
14.51 kg |
29.02 kg |
|
36.28 kg |
29.02 kg |
43.54 kg |
|
58.05 kg |
50.80 kg |
65.31 kg |
|
90.71 kg |
79.83 kg |
101.60 kg |
This
is the normal arrangement with your component
directly on top of VIBRAPOD
Isolators. This assumes a flat bottom with short feet.
|
|
|
|
|
|
|
|
In
some instances it may be necessary to make a VIBRAPOD
Sandwich because the bottom of your component is irregular or the feet
used by the manufacturer are too tall.
In this arrangement you normal shelf acts as a base for the VIBRAPOD
Isolators and a second shelf sits on top of them and your equipment on the
second shelf. This is the best way to isolate a Turntable.
|
|
||
|
|
|
|
 |
|
|
The
Heavier On One Side Problem
Combinations of Models 1, 2, 3, 4,
and 5 VIBRAPOD Isolators will alleviate this problem.
Place the Model 3, 4 or 5 VIBRAPOD Isolators under the
heaviest area of your component and either the Model 1, 2 or 3 VIBRAPOD
Isolators under the lighter areas. This way you can mix and match for the
best effect.
The Second Method Using
One Model VIBRAPOD
Isolator
You can't just put VIBRAPOD
Isolators along front and back, because the weight distribution is so uneven.
For the VIBRAPOD Isolators to work their magic properly,
the equipment is going to sit off-center on a new shelf.
1. Determine shelf depth. First, you take a birch
dowel or a broom handle and slide it under the chassis. Now, gently roll the amp
front to back over the dowel, until you find the center of gravity, and mark
this point on each of the sides of the chassis. Measure the distance from that
point to the back of the amp, and to the front. Which one is bigger? Probably
it'll be the front. Okay, take that dimension and multiply by 2. To this
subtotal, add 1 inch or 2.5cm, to get the total front-to-back depth of the
shelf. Still with me? To get the width of the shelf,
2. Determine shelf width. The L-to-R center of
gravity is probably pretty close to the middle of the chassis, since most audio
equipment is symmetrical in this orientation, but if you have a lot of weight
offset from one side to the other, you'll have to do the calculations a second
time, with the chassis balanced the dowel running from front to back. Otherwise,
if pretty symmetrical, just measure the full width of the chassis and add 1 inch
or 2.5cm.
3. Procure the shelf, in one of the materials
mentioned above. You weigh the shelf and add its weight to that of the
component. This gives you the total amount that the VIBRAPOD
Isolators will be supporting. Now divide by 2.5, 6, 10, 16, or 25 (depending on
which model) to get the number of VIBRAPOD Isolators
used. Put the VIBRAPOD Isolators down on the surface where your
component will live, donut side up. Arrange them symmetrically from front to
back and side to side around the perimeter, not worrying about the uneven weight
distribution of the amp. Put the shelf on top of the VIBRAPOD
Isolators. Last, place the amp on top of the shelf, positioning it so that its
front and side edges are 1/2-inch (1.25cm) in from the front and side edges of
the shelf.
Do not put VIBRAPOD Isolators in a close triangular formation. By close we mean touching as in the illustration below.
VIBRAPOD Isolators may be stacked but we see no real benefits unless you want to transfer money from your account to ours.
It is easiest placing VIBRAPOD Isolators using several wood blocks under the sides of your equipment and then sliding the VIBRAPOD Isolators in using a long spoon or fork. They will slide easiest with the Dome facing up.
Hot Amplifiers
will require that the dome is facing down for best results. Otherwise use the
next Higher Model VIBRAPOD Isolator under the heaviest and hottest area of the amp.
Prezzi e prodotti aggiornati sul nuovo sito Audiokit e-Shop cliccando qui !
Update prices & products on new e-Shop Audiokit website click Here
mercoledì 02 luglio 2014